[毕业设计]双头可调立式钻床设计论文下载

内容简介:

摘    要
    此次设计为可调立式双头钻床的机械设计。设计主要介绍了可调立式双头钻床的设计原理、调整方法及设计计算过程。通过预先给定的加工要求可确定所需的计算参数,进而依据可调立式双头钻床的设计原理来设计计算并校核各个部位的零件,然后进行组装。本次设计可从五大方面进行设计。通过预先给定的加工要求计算并进行了可调式双头钻头的设计、传动系统减速箱的设计、传动系统电机的选用、 X-Y工作台的设计、钻头轴向进给系统的设计共五部的设计。通过设计并组装后的钻床可以一次加工两孔,且两钻头间的距离可调,从而实现可以在一个工件上加工多对两两间距不同的孔。在人力和设备不增加的情况下使用可调立式双头钻床可以成倍提高钻床的加工效率,并可以保证较高的加工精度和孔间相对位置精度。
关键词:滚珠丝杠;电动机;变速箱;可调式双头钻头
 ABSTRACT
The machine design is to devise an adjustable vertical double-headed drilling machine. The design mainly introduced the design principle, adjusting and design calculation process for devise a adjustable vertical double-headed drilling machine. Through the processing requirements given in advance can determine the computation parameters, then based on the design principle, which is about adjustable vertical double-headed drilling machine, to design ,calculate and check each place parts, and then to assemble all the parts. The design can be devised from five aspects. Through the processing requirements given in advance,five parts of the design, the adjustable double transmission system, design of the reducer drive system for the motor selection, design of X-Y workbench, design of axial feeding system for drill bits, can be calculated and devised. Through design and assembly of the drilling machine, two holes can be formed after one processing, and the distance between the two holes can be adjusted. So as to realize processing some groups of holes with different space between two holes. Adjustable vertical two-headed drilling machine can multiply processing efficiency without increase human and equipment, and can guarantee a high machining accuracy and precision of the relative position between holes.

Key words:Ball screw;motor;gearbox;Adjustable two-headed drill bit.

摘    要
ABSTRACT
1 前言
1.1 本课题的背景和研究意义
1.2 本课题解决的问题和设计时主要的工作
2 双头钻床结构设计的总体方案
2.1钻床总体结构
2.2设计方案选择
3 可调式双头钻头的设计
3.1 预选加工材料,加工直径
3.2 计算高速钢麻花钻轴向切削力及扭矩
3.2.1 计算单个钻头轴向切削力
3.2.2 计算单个钻头扭矩
3.3 钻头中各轴及齿轮的计算
3.3.1 齿轮8、9、10、11的计算
3.3.2 齿轮5、6、7的计算
3.4 双头钻头内各轴的设计
3.4.1 计算轴I、VIII的最小直径
3.4.2 计算轴II、VII的最小直径
3.4.3 计算轴III的最小直径
4传动系统减速箱设计
4.1减速箱内各齿轮设计
4.1.1传动系统减速箱齿轮的设计
4.1.2传动系统减速箱齿轮的设计
4.2 双头钻头内各轴的设计
4.2.1 计算轴III的最小直径
4.2.2 计算轴IV的最小直径
4.2.3 计算轴V的最小直径
4.2.4 计算轴VI的最小直径
5 传动系统电机的选用
5.1计算折算到电机主轴上的转矩
6钻头轴向进给系统的设计
6.1 钻头轴向进给丝杠螺母副的计算和选型
6.1.1工作台基本参数
6.1.2计算进给牵引力
6.1.3计算最大动载荷C
6.1.4滚珠丝杠螺母副的选型
6.1.5 传动效率计算
6.1.6刚度检验
6.1.7稳定性校核
6.2齿轮传动比计算
6.3步进电机的计算和选型
6.3.1初选电机型号
6.3.2电机校核计算
7 X-Y工作台的设计
7.1工作台滚珠丝杠螺母副的计算和选型
7.1.1工作台基本参数
7.1.2计算进给牵引力
7.2轨道的选择
8结    论
参 考 文 献
致    谢

为您推荐

返回顶部
首页
电子图书
视频教程
搜索
会员